中興B860AV1.1尋找固件和刷機方法

luoren123 · 發表于 2018-1-14 16:15

本帖最后由 wuli小茶于 2018-1-14 21:26 編輯

第一次用STB和盒子助手破解成功，但重新啟動后系統升級，失敗了。恢復到出廠設置用5位隨機碼打開ADB安裝成功，再重新啟動又被強制升級，再也回不到出廠設置了。隨機碼是C12345的六位數，PUTTY跑碼但不能進入命令提示行。目前版本附圖。

AC_ON
MIU0_DQS-OK
BIST0-???
MIU0-1024_U
Start uboot

Relocation Offset is: 015d7000
[AT][MB][start ub][556]

U-Boot 2011.06-00114-ga7f97e5-dirty (Oct 23 2017 - 23:15:16)

[MIU INFO] miu opencreate instance at 51be9418 with private size 80 bytes at 51be9460
create instance at 51be94b8 with private size 52 bytes at 51be9500

uboot held at [519ddf60~52d00000],size=013220a0
CPU  : Clippers
Board: BD_MST207C_D01A_S_CLIPPERS
DRAM:  813 MiB
Now running in RAM - U-Boot at: 51e00000

eMMC: HS200 200MHz
eMMC 7.28 GB [E8FFF8h]
In: serial
Out: serial
Err: serial
Net: zte_shutdow =false
No ethernet found.
Set MAC default
MAC:  0x0: 0x30: 0x1b: 0xba:0x2: 0xdb
msIR_Initialize

[CPU INFO] cpu opencreate instance at 51bf99c0 with private size 44 bytes at 51bf9a08
CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[38]: MODULE_CPU

[AT][MBoot][Driver Init][765]
### main_loop entered: s is true

### main_loop entered: bootdelay=1

Starting logo
============= set bootargs ===============
[setup_com_controlenv] COMControlFlag=> value[1]=, val=0
zte_mac=D0:71:C4:16:05:F5,ethaddr=D0:71:C4:16:05:F5
Hit any key to stop autoboot: 1@
step1 error...
abort=0                                                                      0
do_bootcheck called
MMC_CAPACITY_512 =15269880
current emmc size is =0xe8fff8 (should by 512)
MMCusrdata_size =11773944

current userdata size =0xb3a7f8 (should by 512)
this is 8G emmc
get_boot1_ver cmd_boot1=mmc read.boot 1 0x25000000 0x0 0x200000
set hdmi hdcp mode 0!
Saving Environment to MMC...
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
iTVSTandard2Resolution = 2
value[29] = 50100499007034400000D071C41605F5
[setup_bootenv] COMControlFlag=> value[30]=, val=0
ethaddr =D0:71:C4:16:05:F5
jy ....
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
[ztebsp] BootMode=0
[do_bootcheck,1181][ZTEWatchdog]PATCH FOR zte BEGIN
[do_bootcheck,1185][ZTEWatchdog] Watchdog_enable TRUE
[do_bootcheck,1191][ZTEWatchdog] Watchdog start, MAXTIME 120
create instance at 51bf9bb0 with private size 256 bytes at 51bf9bf8
MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000
MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000
PNL:[MDrv_PNL_SetPanelType][613]
[_MDrv_PNL_Init_LPLL][323]pstPanelInitData->u16Width=1280, pstPanelInitData->u16Height=720
[_MDrv_PNL_Init_LPLL][325]u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
[_MDrv_PNL_Init_Output_Dclk][369]pstPanelInitData->u16Width=1280, pstPanelInitData->u16Height=720
[_MDrv_PNL_Init_Output_Dclk][371]u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
PNL:CalculateLPLLSETbyDClk u32KHz = 742500000, u64DefaultLdHz = 742500000
PNL:CalculateLPLLSETbyDClk u32LpllSet = 3531df
[MApi_XC_MLG_GetStatus, 1603]No instance existed, please get an instance by calling MApi_XC_Init() first
msHdmitx_Disp_Init
create instance at 51bf9d00 with private size 1720 bytes at 51bf9d48
[XC,Version]
no need to patchcreate instance at 51bfa948 with private size 80 bytes at 51bfa990
Rx Support HDMI mode!
setHDMITxAnalogTuning: Error: MApi_HDMITx_GetRxDCInfoFromEDID EDID is not ready, at 262
shift -8 pixels in PAL mode
Create Dolby single part name task failed!![Hal_VE_Set_PreHSD][1826] ERROR!!! HVSD H input = 0, HVSD H output = 720
[Hal_VE_Set_PreVSD][2002] ERROR!!! HVSD V input = 0, HVSD V output = 576
[Hal_VE_EnableDI][2110] bEnable = 0, bIsDNR2VE = 0
lyndon Hal_VE_Set_PreVSD 1mmc change mount : tvcustomer
Size of file "/720.jpg" from mmc device 0 partition tvcustomer: 151757 bytes
Loading file "/720.jpg" at offset 0x0 from mmc device 0 partition tvcustomer
151757 bytes read
create instance at 51bfa9e8 with private size 304 bytes at 51bfaa30
[AT][MB][JPD Decode][2424]

[UTOPIA INFO] close moduleNames[35]: MODULE_NJPEG_EX

create instance at 51bfa9e8 with private size 132280 bytes at 51bfaa30

[GOP INFO] gop opencreate instance at 51c1aef0 with private size 6908 bytes at 51c1af38
[AT][MB][Show Logo][2463]
## Booting kernel from Legacy Image at 25000800 ...
Image Name: MStar-linux
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 5317432 Bytes = 5.1 MiB
Load Address: 20208000
Entry Point:  20208000
Contents:
   Image 0: 4627208 Bytes = 4.4 MiB
   Image 1: 690212 Bytes = 674 KiB
## Loading init Ramdisk from multi component Legacy Image at 25000800 ...
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Loading Multi-File Image ... OK
[AT][MB][start kr][2708]

Starting kernel ...

[PROTECT ERROR], not expected dram size: 0x0
#######################################################################
# [PROTECT WARNING], miu kernel protect is not enabled on second dram #
#######################################################################
Uncompressing Linux... done, booting the kernel.
KERN-3.10.23.001049551
tommy: thread_info_cache_init
mtdoops: mtd device (mtddev=name/number) must be supplied
[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2196] ready init mutex

[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2197] after init mutex
RBQP_BASE = 50304000
init: /init.clippers.rc: 455: ignored duplicate definition of service 'mdnsd'
init: /zte_init.rc: 38: ignored duplicate definition of service 'xiriservice'
init: ## ProductID: strlen (32)!
healthd: No charger supplies found
init: cannot find '/system/bin/xiriservice_ChinaMobile_SiChuan', disabling 'bluetoothd'
init: cannot find '/system/bin/bleservice', disabling 'bleservice'

luoren123 · 發表于 2018-1-16 15:16

286890528 發表于 2018-1-16 14:33
你找找自帶的網絡測速我的系統自帶的是當貝助手圖標名字是網絡測速里面有文件快傳的功能在電腦網 ...

貝當助手沒有電腦版的，手機版的網絡測速里面沒有別的功能

eggttbaby · 發表于 2018-1-14 21:26

幫頂，祝早日解決

xxxjguo · 發表于 2018-1-15 10:46

老鐵666！必須支持一波！

ronin0215 · 發表于 2018-1-15 14:45

我的是s905的u，直接直接線刷了事。。。。。。。

luoren123 · 發表于 2018-1-15 19:57

ronin0215 發表于 2018-1-15 14:45
我的是s905的u，直接直接線刷了事。。。。。。。

有B860AV1.1的固件嗎?用B860AV2.1的固件刷可以嗎?

luoren123 · 發表于 2018-1-15 19:59

ronin0215 發表于 2018-1-15 14:45
我的是s905的u，直接直接線刷了事。。。。。。。

有B860AV1.1的固件嗎?用B860AV2.1的固件刷可以嗎?
我的郵箱:13914274104ren@sina.com.

286890528 · 發表于 2018-1-16 11:05

和我的一樣無法TTL 無法ADB 無法U盤降級最后用系統自帶的網絡測試（當貝助手）中的文件快傳功能從電腦上傳軟件安裝在盒子上成功破解

luoren123 · 發表于 2018-1-16 14:18

286890528 發表于 2018-1-16 11:05
和我的一樣無法TTL 無法ADB 無法U盤降級最后用系統自帶的網絡測試（當貝助手）中的文件快傳功能從電 ...

關鍵是如何打開盒子傳送文件，當貝助手可以傳文件到盒子？這要試試。

286890528 · 發表于 2018-1-16 14:33

luoren123 發表于 2018-1-16 14:18
關鍵是如何打開盒子傳送文件，當貝助手可以傳文件到盒子？這要試試。

你找找自帶的網絡測速我的系統自帶的是當貝助手圖標名字是網絡測速里面有文件快傳的功能在電腦網頁上輸網址就能傳軟件到機頂盒

antcipate · 發表于 2018-1-23 18:37

我的和你的一樣，TTL不斷重啟，提示少文件。HDMI連電視也是不斷重啟，還沒設置完就重啟了，坑啊

gnsx · 發表于 2018-2-5 14:55

286890528 發表于 2018-1-16 11:05
和我的一樣無法TTL 無法ADB 無法U盤降級最后用系統自帶的網絡測試（當貝助手）中的文件快傳功能從電 ...

OK，謝謝指點。

gla_1110 · 發表于 2018-2-5 21:11

尾號GA。高安檢測的盒子。容易磚，千玩別折騰ROOT，一折騰救容易磚頭

kkkh100123 · 發表于 2018-2-12 00:27

和你一毛一樣，，，沒辦法了

極度霸氣 · 發表于 2018-2-16 00:40

1234

› 你問我答 / 玩機教程 / 固件 › ROM固件下載

中興B860AV1.1尋找固件和刷機方法

中興B860AV1.1尋找固件和刷機方法

相關帖子