cm211-1-zg，TTL跑馬問題

temp_007 · 發表于 2022-5-5 14:29

GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 77558

BL2 Built : 13:36:55, Jun 22 2020n
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 4, adc=303
set vcck to 1070 mv
set vddee to 1070 mv
CARD_3 high, old board
CPU clk: 1200MHz

DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz
bist_test rank: 0 25 03 48 3b 1a 5c 26 00 4c 3d 1c 5f 26 02 4a 3b 1a 5d 25 01 4a             3b 17 5f 612 - PASS

Rank0: 2048MB(auto)-2T-11
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002400
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x0007b000
NOTICE:  BL3-1: v1.0(debug):361f8a7
NOTICE:  BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23 yao.zhang@droid07]
efuse init ops = c5
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 d4 b3 60 a0 0 c5 not ES chip
[0.622990 Inits done]
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01 (Mar 29 2021 - 17:09:00)

DRAM:  2 GiB
Relocation Offset is: 76e8c000
this uboot is for hw_1_8, set GPIODV_24gpio: pin GPIODV_24 (gpio 43) value is 1
gpio: pin GPIOZ_14 (gpio 73) value is 1
register usb cfg[0][1] = 0000000077f5bc10
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073e7cc00
aml_priv->desc_buf = 0x0000000073e7ef20
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
[mmc_init] mmc init success
dtb magic 08088b1f
   Amlogic multi-dtb tool
   GZIP format, decompress...
   Multi dtb detected
   unified board, board id = 4
   Multi dtb tool version: v2 .
   Support 10 dtbs.
      aml_dt soc: gxl platform: p211 variant: 2g
      dtb 0 soc: gxl plat: p211 vari: 1g
      dtb 1 soc: gxl plat: p211 vari: 2g
      dtb 2 soc: gxlx plat: p261 vari: 1g
      dtb 3 soc: gxlx plat: p261 vari: 2g
      dtb 4 soc: gxlx plat: p265 vari: 1g
      dtb 5 soc: gxlx plat: p265 vari: 2g
      dtb 6 soc: gxlx2 plat: p291 vari: 1g
      dtb 7 soc: gxlx2 plat: p291 vari: 2g
      dtb 8 soc: gxlx2 plat: p295 vari: 1g
      dtb 9 soc: gxlx2 plat: p295 vari: 2g
   Find match dtb: 1
start dts,buffer=0000000073e81750,dt_addr=0000000073e81750
   Amlogic multi-dtb tool
   Single dtb detected
parts: 13
00:    logo 0000000002000000 1
01:  recovery 0000000002000000 1
02:    rsv 0000000000800000 1
03:    tee 0000000000800000 1
04:    crypt 0000000002000000 1
05:    misc 0000000002000000 1
06: instaboot 0000000020000000 1
07:    boot 0000000002000000 1
08: system 0000000040000000 1
09:    cache 000000002d000000 2
10: params 0000000004000000 2
11: bootfiles 000000002d000000 2
12:    data ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x34400000
In: serial
Out: serial
Err: serial
board id is : 4
hpd_state=0
cvbs performance type = 7, table = 1
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-924: calc 9f88d8d1, store 9f88d8d1
_verify_dtb_checksum()-924: calc 9f88d8d1, store 9f88d8d1
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
   Amlogic multi-dtb tool
   GZIP format, decompress...
   Multi dtb detected
   unified board, board id = 4
   Multi dtb tool version: v2 .
   Support 10 dtbs.
      aml_dt soc: gxl platform: p211 variant: 2g
      dtb 0 soc: gxl plat: p211 vari: 1g
      dtb 1 soc: gxl plat: p211 vari: 2g
      dtb 2 soc: gxlx plat: p261 vari: 1g
      dtb 3 soc: gxlx plat: p261 vari: 2g
      dtb 4 soc: gxlx plat: p265 vari: 1g
      dtb 5 soc: gxlx plat: p265 vari: 2g
      dtb 6 soc: gxlx2 plat: p291 vari: 1g
      dtb 7 soc: gxlx2 plat: p291 vari: 2g
      dtb 8 soc: gxlx2 plat: p295 vari: 1g
      dtb 9 soc: gxlx2 plat: p295 vari: 2g
   Find match dtb: 1
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 16
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[CANVAS]addr=0x3dc00000 width=3840, height=2160
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[ch_code] not programed yet
rebootmode=cold_boot
Enter USB burn
Try connect time out 701, 700, 853
key1 = 7d82dd22
key2 = 7e81dd22
key3 = 728ddd22
time_out = 7a120
ir init
irkey - irkey key_value1 key_value2 key_value3 time_value

Usage:
irkey
Hit any key to stop autoboot:  0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73ec1970
copy done
   Amlogic multi-dtb tool
   Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x020910f0
Loading Ramdisk to 73d7e000, end 73e7a4bd ... OK
Loading Device Tree to 000000000fff3000, end 000000000ffff8c7 ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 3265586 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g18c40508-dirty (wangchong@T2) (gcc version 4.9.1 20140529 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.07 - Linaro GCC 4.9-2014.06) ) #11 SMP PREEMPT Mon Apr 19 15:57:15 CST 2021
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0004
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
WARNING: Unimplemented Sip Call: 0x82000036

卡在這步了，不再跑，進入不了用戶名下，或者啟動過程也進入不了UBOOT，求幫忙。

橙子的甜 · 發表于 2022-5-5 14:41

重新在刷一下試試

temp_007 · 發表于 2022-5-5 15:39

本帖最后由 temp_007 于 2022-5-5 16:26 編輯

總是出錯

temp_007 · 發表于 2022-5-5 15:40

重新刷哪種包呢

temp_007 · 發表于 2022-5-5 15:40

重新刷哪種包呢

temp_007 · 發表于 2022-5-5 15:40

重新刷，哪一種包，可以通過？

水有嘉魚 · 發表于 2022-5-5 15:53

短接刷

temp_007 · 發表于 2022-5-5 16:17

短接刷也試過，還是在這個提示后不跑馬

temp_007 · 發表于 2022-5-5 16:18

短接后也試過，還是這個提示通不過。

temp_007 · 發表于 2022-5-5 18:34

？？？？

› 你問我答 / 玩機教程 / 固件 › ZNDS刷機/救磚